cu -l /dev/tty00 -s 19200 POST: 0123456789bcefghipajklnoq,,,tvwxy comBIOS ver. 1.20 20030721 Copyright (C) 2000-2003 Soekris Engineering. net4801 CPU Geode 266 Mhz 0128 Mbyte Memory Pri Mas TOSHIBA THNCF064MBA LBA 978-4-32 62 Mbyte PXE-M00: BootManage UNDI, PXE-2.0 (build 082) Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int ------------------------------------------------------------------- 0:00:0 1078 0001 06000000 0107 0280 00 1F 00 00000000 00000000 00 0:06:0 100B 0020 02000000 0107 0290 00 3F 00 0000E101 A0000000 10 0:07:0 100B 0020 02000000 0107 0290 00 3F 00 0000E201 A0001000 10 0:08:0 100B 0020 02000000 0107 0290 00 3F 00 0000E301 A0002000 10 0:18:2 100B 0502 01018001 0005 0280 00 00 00 00000000 00000000 00 0:19:0 0E11 A0F8 0C031008 0117 0280 08 38 00 A0003000 00000000 11 Seconds to automatic boot. Press Ctrl-P for entering Monitor. 5 Using Drive: 0 Partition: 3 reading boot..... probing: pc0 com0 com1 pci mem[639K 63M a20=on] disk: hd0+ >> OpenBSD/i386 BOOT 2.01 switching console to com0 com0: changing speed to 19200 baud com0: change your terminal to match! com0: will change speed in 5 seconds.... com0: console is at 19200 baud boot> booting hd0a:/bsd: 4510548+838332+206144+183657=0x5792c4 entry point at 0x100120 [ using 390324 bytes of bsd ELF symbol table ] Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2003 OpenBSD. All rights reserved. http://www.OpenBSD.org OpenBSD 3.4-beta (xatu) #0: Sat Aug 23 17:02:01 CEST 2003 root@xatu.internal.kd85.com:/usr/obj/xatu cpu0: National Semiconductor Geode GX1 ("Geode by NSC" 586-class) 267 MHz cpu0: FPU,TSC,MSR,CX8,CMOV,MMX real mem = 66695168 (65132K) avail mem = 55926784 (54616K) using 839 buffers containing 3436544 bytes (3356K) of memory mainbus0 (root) bios0 at mainbus0: AT/286+(00) BIOS, date 20/30/21, BIOS32 rev. 0 @ 0xf7840 pcibios0 at bios0: rev. 2.0 @ 0xf0000/0x10000 pcibios0: pcibios_get_intr_routing - function not supported pcibios0: PCI IRQ Routing information unavailable. pcibios0: PCI bus #0 is the last bus bios0: ROM list: 0xc8000/0xa000 pci0 at mainbus0 bus 0: configuration mode 1 (bios) pchb0 at pci0 dev 0 function 0 "Cyrix GXm Host-PCI" rev 0x00 sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00: irq 10 address 00:00:24:c1:35:b8 nsphyter0 at sis0 phy 0: DP83815 10/100 integrated, rev. 1 sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00: irq 10 address 00:00:24:c1:35:b9 nsphyter1 at sis1 phy 0: DP83815 10/100 integrated, rev. 1 sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00: irq 10 address 00:00:24:c1:35:ba nsphyter2 at sis2 phy 0: DP83815 10/100 integrated, rev. 1 pcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00 "NS SC1100 SMI/ACPI" rev 0x00 at pci0 dev 18 function 1 not configured pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA (unsupported), channel 0 wired to compatibility, channel 1 wired to compatibility pciide0: channel 0 ignored (other hardware responding at addresses) pciide0: channel 1 ignored (not responding; disabled or no drives?) "NS SC1100 X-Bus" rev 0x00 at pci0 dev 18 function 5 not configured ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 11, OHCI version 1.0, legacy support usb0 at ohci0: USB revision 1.0 uhub0 at usb0 uhub0: Compaq OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 3 ports with 3 removable, self powered isa0 at pcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard wdc0 at isa0 port 0x1f0/8 irq 14 wd0 at wdc0 channel 0 drive 0: wd0: 1-sector PIO, LBA, 61MB, 978 cyl, 4 head, 32 sec, 125184 sectors wd0(wdc0:0:0): using BIOS timings pcppi0 at isa0 port 0x61 midi0 at pcppi0: sysbeep0 at pcppi0 npx0 at isa0 port 0xf0/16: using exception 16 pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo pccom0: console pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo biomask 4800 netmask 4c00 ttymask 4c02 pctr: user-level cycle counter enabled dkcsum: wd0 matched BIOS disk 80 root on wd0a rootdev=0x0 rrootdev=0x300 rawdev=0x302 WARNING: clock time much less than file system time WARNING: using file system time WARNING: CHECK AND RESET THE DATE! /dev/rwd0a: file system is clean; not checking mfs: mounting /tmp... mfs: populating /tmp... databases: dev securelevel: kern.securelevel: 0 -> 1 watchdog: sysctl: kern.watchdog.period: value is not available watchdog: sysctl: kern.watchdog.auto: value is not available hostname: setting hostname to soekris... inet: configuring IP on system interfaces... route: adding default route... add net default: gateway 208.192.32.1 pf/nat: configuring and enabling... pf enabled syslogd: starting log daemon... ssh: starting daemon... root password is x OpenBSD/i386 (soekris) (tty00) login: root Password: # reboot syncing disks... done rebooting...