POST: 0123456789bcefghips1234ajklnopqr,,,tvwxy

comBIOS ver. 1.40a  20110906  Copyright (C) 2000-2011 Soekris Engineering.

net6501

CPU Atom E6xx 1009 Mhz 1024 Mbyte Memory

Initializing Intel(R) Boot Agent GE v1.3.72
PXE 2.1 Build 089 (WfM 2.0)

SATA AHCI BIOS ver. 0.6 20110902  Copyright (C) 2003-2011 Intel Corporation

Controller Bus#02, Device#06, Function#00: 02 Ports, 01 Devices
  Port-00: No device detected
  Port-01: Hard Disk, SanDisk CompactFlash 200x      

 Slot   Vend Dev  ClassRev Cmd  Stat CL LT HT  Base1    Base2   Int 
--------------------------------------------------------------------
00:00:0 8086 4114 06000003 0007 0000 00 00 00 00000000 00000000 
00:23:0 8086 8184 06040000 0107 0010 08 00 01 1FFF1000 A0FFA000 10
00:24:0 8086 8185 06040000 0107 0010 08 00 01 3FFF2000 A2FFA100 11
00:25:0 8086 8180 06040000 0107 0010 08 00 01 5FFF4000 A4FFA300 05
00:26:0 8086 8181 06040000 0107 0010 08 00 01 0FFF1000 00FFA000 09
00:31:0 8086 8186 06010000 0003 0000 00 00 80 00000000 00000000 
02:02:0 8086 8804 0C031001 0106 0010 00 00 80 A0000900 00000000 09
02:02:1 8086 8805 0C031001 0106 0010 00 00 80 A0000A00 00000000 09
02:02:2 8086 8806 0C031001 0106 0010 00 00 80 A0000B00 00000000 09
02:02:3 8086 8807 0C032001 0106 0010 00 00 80 A0000C00 00000000 09
02:06:0 8086 880B 01060101 0107 0010 00 00 00 00000000 00000000 11
02:08:0 8086 880C 0C031001 0106 0010 00 00 80 A0004400 00000000 10
02:08:1 8086 880D 0C031001 0106 0010 00 00 80 A0004500 00000000 10
02:08:2 8086 880E 0C031001 0106 0010 00 00 80 A0004600 00000000 10
02:08:3 8086 880F 0C032001 0106 0010 00 00 80 A0004700 00000000 10
02:10:1 8086 8811 07000200 0107 0010 00 00 80 00001021 A0004800 09
02:10:2 8086 8812 07000200 0107 0010 00 00 80 00001029 A0004810 09
02:12:2 8086 8817 0C800000 0106 0010 00 00 80 00000000 A0004900 05
02:12:3 8086 8818 0C090000 0106 0010 00 00 80 00000000 A0004A00 05
03:00:0 111D 803A 0604000E 0107 0010 08 00 01 3FFF2000 A2FFA100 
05:00:0 8086 10D3 02000000 0107 0010 08 00 00 A1000000 00000000 09
06:00:0 8086 10D3 02000000 0107 0010 08 00 00 A2000000 00000000 10
08:00:0 111D 803A 0604000E 0107 0010 08 00 01 5FFF4000 A4FFA300 
10:00:0 8086 10D3 02000000 0107 0010 08 00 00 A3000000 00000000 10
11:00:0 8086 10D3 02000000 0107 0010 08 00 00 A4000000 00000000 11

   Seconds to automatic boot.   Press Ctrl-P for entering Monitor. 5

1  pfSense
2  pfSense

F6 PXE
Boot:  1 
/boot.config: -h
Consoles: serial port  
BIOS drive C: is disk0
BIOS 632kB/1047552kB available memory

FreeBSD/i386 bootstrap loader, Revision 1.1
(sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org, Tue Jun 21 18:03:18 EDT 2011)
Loading /boot/defaults/loader.conf 
/boot/kernel/kernel text=0x899e7c ]
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...               
Copyright (c) 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p4 #0: Tue Jun 21 18:20:40 EDT 2011
    sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_wrap.8.i386 i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Genuine Intel(R) CPU        @ 1.00GHz (1000.01-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x20661  Family = 6  Model = 26  Stepping = 1
  Features=0xbfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x40e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,MOVBE>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant
real memory  = 1073741824 (1024 MB)
avail memory = 1032179712 (984 MB)
ACPI Error: A valid RSDP was not found (20100331/tbxfroot-309)
MPTable: <Soekris  net6501     >
WARNING: Non-uniform processors.
WARNING: Using suboptimal topology.
ioapic0: Assuming intbase of 0
ioapic0 <Version 2.0> irqs 0-23 on motherboard
wlan: mac acl policy registered
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0708970, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0708a10, 0) error 1
wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (wpi_fw, 0xc087b830, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc0708ab0, 0) error 1
ACPI Error: A valid RSDP was not found (20100331/tbxfroot-309)
ACPI: Table initialisation failed: AE_NOT_FOUND
ACPI: Try disabling either ACPI or apic support.
cryptosoft0: <software crypto> on motherboard
padlock0: No ACE support.
pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> irq 16 at device 23.0 on pci0
pci1: <PCI bus> on pcib1
pcib2: <PCI-PCI bridge> irq 16 at device 0.0 on pci1
pci2: <PCI bus> on pcib2
pci2: <unknown> at device 0.0 (no driver attached)
pci2: <network, ethernet> at device 0.1 (no driver attached)
pci2: <unknown> at device 0.2 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xa0000900-0xa00009ff irq 19 at device 2.0 on pci2
ohci0: [ITHREAD]
usbus0: <OHCI (generic) USB controller> on ohci0
ohci1: <OHCI (generic) USB controller> mem 0xa0000a00-0xa0000aff irq 19 at device 2.1 on pci2
ohci1: [ITHREAD]
usbus1: <OHCI (generic) USB controller> on ohci1
ohci2: <OHCI (generic) USB controller> mem 0xa0000b00-0xa0000bff irq 19 at device 2.2 on pci2
ohci2: [ITHREAD]
usbus2: <OHCI (generic) USB controller> on ohci2
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xa0000c00-0xa0000cff irq 19 at device 2.3 on pci2
ehci0: [ITHREAD]
usbus3: EHCI version 1.0
usbus3: <EHCI (generic) USB 2.0 controller> on ehci0
pci2: <serial bus, USB> at device 2.4 (no driver attached)
pci2: <base peripheral, SD host controller> at device 4.0 (no driver attached)
pci2: <base peripheral, SD host controller> at device 4.1 (no driver attached)
atapci0: <Intel AHCI controller> port 0x1000-0x101f mem 0xa0004000-0xa00043ff irq 17 at device 6.0 on pci2
atapci0: [ITHREAD]
atapci0: AHCI v1.10 controller with 2 3Gbps ports, PM supported
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
ohci3: <OHCI (generic) USB controller> mem 0xa0004400-0xa00044ff irq 16 at device 8.0 on pci2
ohci3: [ITHREAD]
usbus4: <OHCI (generic) USB controller> on ohci3
ohci4: <OHCI (generic) USB controller> mem 0xa0004500-0xa00045ff irq 16 at device 8.1 on pci2
ohci4: [ITHREAD]
usbus5: <OHCI (generic) USB controller> on ohci4
ohci5: <OHCI (generic) USB controller> mem 0xa0004600-0xa00046ff irq 16 at device 8.2 on pci2
ohci5: [ITHREAD]
usbus6: <OHCI (generic) USB controller> on ohci5
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xa0004700-0xa00047ff irq 16 at device 8.3 on pci2
ehci1: [ITHREAD]
usbus7: EHCI version 1.0
usbus7: <EHCI (generic) USB 2.0 controller> on ehci1
pci2: <unknown> at device 10.0 (no driver attached)
pci2: <simple comms, UART> at device 10.1 (no driver attached)
pci2: <simple comms, UART> at device 10.2 (no driver attached)
pci2: <simple comms, UART> at device 10.3 (no driver attached)
pci2: <simple comms, UART> at device 10.4 (no driver attached)
pci2: <unknown> at device 12.0 (no driver attached)
pci2: <serial bus> at device 12.1 (no driver attached)
pci2: <serial bus> at device 12.2 (no driver attached)
pci2: <serial bus> at device 12.3 (no driver attached)
pci2: <unknown> at device 12.4 (no driver attached)
pcib3: <PCI-PCI bridge> irq 17 at device 24.0 on pci0
pci3: <PCI bus> on pcib3
pcib4: <PCI-PCI bridge> at device 0.0 on pci3
pci4: <PCI bus> on pcib4
pcib5: <PCI-PCI bridge> at device 2.0 on pci4
pci5: <PCI bus> on pcib5
em0: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0x2000-0x201f mem 0xa1000000-0xa101ffff,0xa1020000-0xa1023fff irq 19 at device 0.0 on pci5
em0: Using MSIX interrupts with 3 vectors
em0: [ITHREAD]
em0: [ITHREAD]
em0: [ITHREAD]
pcib6: <PCI-PCI bridge> at device 3.0 on pci4
pci6: <PCI bus> on pcib6
em1: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0x3000-0x301f mem 0xa2000000-0xa201ffff,0xa2020000-0xa2023fff irq 16 at device 0.0 on pci6
em1: Using MSIX interrupts with 3 vectors
em1: [ITHREAD]
em1: [ITHREAD]
em1: [ITHREAD]
pcib7: <PCI-PCI bridge> at device 4.0 on pci4
pci7: <PCI bus> on pcib7
pcib8: <PCI-PCI bridge> irq 18 at device 25.0 on pci0
pci8: <PCI bus> on pcib8
pcib9: <PCI-PCI bridge> at device 0.0 on pci8
pci9: <PCI bus> on pcib9
pcib10: <PCI-PCI bridge> at device 2.0 on pci9
pci10: <PCI bus> on pcib10
em2: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0x4000-0x401f mem 0xa3000000-0xa301ffff,0xa3020000-0xa3023fff irq 16 at device 0.0 on pci10
em2: Using MSIX interrupts with 3 vectors
em2: [ITHREAD]
em2: [ITHREAD]
em2: [ITHREAD]
pcib11: <PCI-PCI bridge> at device 3.0 on pci9
pci11: <PCI bus> on pcib11
em3: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0x5000-0x501f mem 0xa4000000-0xa401ffff,0xa4020000-0xa4023fff irq 17 at device 0.0 on pci11
em3: Using MSIX interrupts with 3 vectors
em3: [ITHREAD]
em3: [ITHREAD]
em3: [ITHREAD]
pcib12: <PCI-PCI bridge> at device 4.0 on pci9
pci12: <PCI bus> on pcib12
pcib13: <PCI-PCI bridge> irq 19 at device 26.0 on pci0
pci13: <PCI bus> on pcib13
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
cpu0 on motherboard
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
atrtc0: <AT Real Time Clock> at port 0x70 irq 8 on isa0
ppc0: parallel port not found.
uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
uart0: [FILTER]
uart0: console (9600,n,8,1)
Timecounter "TSC" frequency 1000005900 Hz quality 800
Timecounters tick every 10.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
ugen0.1: <(0x8086)> at usbus0
uhub0: <(0x8086) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <(0x8086)> at usbus1
uhub1: <(0x8086) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
ugen2.1: <(0x8086)> at usbus2
uhub2: <(0x8086) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
uhub0: 1 port with 1 removable, self powered
uhub1: 1 port with 1 removable, self powered
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
uhub2: 1 port with 1 removable, self powered
ugen4.1: <(0x8086)> at usbus4
uhub4: <(0x8086) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <(0x8086)> at usbus5
uhub5: <(0x8086) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
ugen6.1: <(0x8086)> at usbus6
uhub6: <(0x8086) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
ugen7.1: <Intel> at usbus7
uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
uhub4: 1 port with 1 removable, self powered
uhub5: 1 port with 1 removable, self powered
ad6: 3815MB <SanDisk CompactFlash 200x HDX 6.03> at ata3-master PIO4 SATA 1.5Gb/s
uhub6: 1 port with 1 removable, self powered
Root mount waiting for: usbus7 usbus3
uhub3: 3 ports with 3 removable, self powered
uhub7: 3 ports with 3 removable, self powered
Trying to mount root from ufs:/dev/ufs/pfsense0
Invalid time in real time clock.
Check and reset the date immediately!
Configuring crash dumps...
Mounting filesystems...
Setting up embedded specific environment... done.

     ___
 ___/ f \
/ p \___/ Sense
\___/   \
    \___/

Welcome to pfSense 2.0-RC3  ...

Creating symlinks....ad6: TIMEOUT - READ retrying (1 retry left) LBA=1026271
..done.
External config loader 1.0 is now starting... ad6s3
appending output to nohup.out
Launching the init system... done.
Initializing............................ done.
Starting device manager (devd)...done.
Loading configuration......done.

Network interface mismatch -- Running interface assignment option.

Valid interfaces are:

em0   00:00:24:ce:45:74   (up) Intel(R) PRO/1000 Network Connection 7.2.3
em1   00:00:24:ce:45:75   (up) Intel(R) PRO/1000 Network Connection 7.2.3
em2   00:00:24:ce:45:76   (up) Intel(R) PRO/1000 Network Connection 7.2.3
em3   00:00:24:ce:45:77   (up) Intel(R) PRO/1000 Network Connection 7.2.3

Do you want to set up VLANs first? 

If you are not going to use VLANs, or only for optional interfaces, you should
say no here and use the webConfigurator to configure VLANs later, if required.

Do you want to set up VLANs now [y|n]? n
	
*NOTE*  pfSense requires *AT LEAST* 1 assigned interface(s) to function.
        If you do not have *AT LEAST* 1 interfaces you CANNOT continue. 

        If you do not have at least 1 *REAL* network interface card(s)
        or one interface with multiple VLANs then pfSense
        *WILL NOT* function correctly.

If you do not know the names of your interfaces, you may choose to use
auto-detection. In that case, disconnect all interfaces now before
hitting 'a' to initiate auto detection.
	
Enter the WAN interface name or 'a' for auto-detection: em0

Enter the LAN interface name or 'a' for auto-detection 
NOTE: this enables full Firewalling/NAT mode.
(or nothing if finished): 

The interfaces will be assigned as follows: 

WAN  -> em0
	
Do you want to proceed [y|n]?y

Writing configuration...done.
Updating configuration...done.
Cleaning backup cache...done.
Setting up extended sysctls...done.
Setting timezone...done.
ad6: TIMEOUT - READ retrying (1 retry left) LBA=961039
Starting Secure Shell Services...done.
Setting up polling defaults...done.
Setting up interfaces microcode...done.
Configuring LAGG interfaces...done.
Configuring VLAN interfaces...done.
Configuring QinQ interfaces...done.
Configuring WAN interface...done.
Syncing OpenVPN settings...done.
Starting syslog...done.
Configuring firewall......done.
Starting PFLOG...done.
Setting up gateway monitors...done.
Synchronizing user settings...ad6: TIMEOUT - READ retrying (1 retry left) LBA=1129975
done.
Starting webConfigurator...done.
Configuring CRON...done.
Starting OpenNTP time client...done.
Starting DNS forwarder...done.
Configuring firewall......done.
Generating RRD graphs...done.
Starting CRON... done.
Bootup complete

FreeBSD/i386 (pfSense.localdomain) (console)

*** Welcome to pfSense 2.0-RC3-nanobsd (i386) on pfSense ***

  WAN (wan)                 -> em0        -> NONE (DHCP)

 0) Logout (SSH only)                  8) Shell
 1) Assign Interfaces                  9) pfTop
 2) Set interface(s) IP address       10) Filter Logs
 3) Reset webConfigurator password    11) Restart webConfigurator
 4) Reset to factory defaults         12) pfSense Developer Shell
 5) Reboot system                     13) Upgrade from console
 6) Halt system                       14) Enable Secure Shell (sshd)
 7) Ping host                         

Enter an option: 6


pfSense will shutdown and halt system. This may take one minute.

Do you want to proceed [y|n]? y

pfSense will shutdown and halt system now.
*** Welcome to pfSense 2.0-RC3-nanobsd (i386) on pfSense ***

  WAN (wan)                 -> em0        -> NONE (DHCP)

 0) Logout (SSH only)                  8) Shell
 1) Assign Interfaces                  9) pfTop
 2) Set interface(s) IP address       10) Filter Logs
 3) Reset webConfigurator password    11) Restart webConfigurator
 4) Reset to factory defaults         12) pfSense Developer Shell
 5) Reboot system                     13) Upgrade from console
 6) Halt system                       14) Enable Secure Shell (sshd)
 7) Ping host                         

Enter an option:                                                                                
*** FINAL System shutdown message from root@pfSense.localdomain ***          
System going down IMMEDIATELY                                                  
                                                                               
                                                                               

pfSense is now shutting down ...

Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...0 0 done
All buffers synced.
Uptime: 3m20s

The operating system has halted.
Please press any key to reboot.

Rebooting...


POST: 0123456789bcefghips1234ajklnopqr,,,tvwxy